A warped part is a part that shrank unevenly. Find where the difference comes from and you have found the fix.
A part comes off the press looking fine. An hour later it is bowed, twisted or no longer flat enough to assemble. Warpage is one of the most frustrating defects in injection molding because the part can look correct at ejection and still fail inspection later.
Every case of warpage comes back to the same idea: different areas of the part shrank by different amounts. Find the source of the difference and you have found the fix. This article is part of our injection molding defect library; see Common Injection Molding Defects and How to Fix Them for the full list.
Three kinds of uneven shrinkage
Plastics Technology describes three ways shrinkage can differ within a part:
- Region to region. Thick areas near the gate and thin areas at the end of fill shrink at different rates.
- Top to bottom (through the thickness). If one side of a wall shrinks more than the other, the part bows. This is often tied to a temperature difference between the two mold halves.
- Direction to direction. Molecules and fibers align with flow. Amorphous materials shrink more parallel to flow, while semi-crystalline materials shrink more perpendicular to it.
The five main causes of warpage
1. Uneven cooling
Cooling is usually the biggest factor. Paulson Training Programs puts the general rule simply: the plastic that cools the slowest shrinks the most. If one side of a wall cools more slowly than the other, that side shrinks more and pulls the part toward it. Corners are a common example: they cool last and can pull side walls inward.
Texas Injection Molding lists imbalanced mold cooling and a large temperature difference between the core and cavity sides as leading causes of warpage.
2. Uneven packing
Cavity pressure is highest near the gate and lower at the far end of the part, so plastic near the gate shrinks less than plastic farther away. A packing profile that works well near the gate can leave the end of fill less dense, and the difference shows up as warp. Reducing packing pressure and lowering melt viscosity can narrow that difference along the length of the part.
3. Molecular and fiber orientation
Fast filling orients molecules in the flow direction, and some of that orientation stays locked in as the part cools, driving shrinkage both right after molding and later. In fiber-reinforced materials, fibers align with flow and shrink less in that direction, which can cause directional warpage if orientation is uneven.
4. Material
Semi-crystalline materials with high, direction-dependent shrinkage, such as polypropylene and nylon, are more prone to warp. Glass- or carbon-fiber reinforced grades generally shrink less and are more dimensionally stable, as long as fiber orientation is controlled.
5. Part design and ejection timing
Uneven wall thickness is a classic cause of warpage. Ribs matter too: PlasticsToday notes that ribs thicker than 50% of the wall can act as heat sinks and suggests a range of 30% to 50% of wall thickness, and that ribs longer than about 20 mm increase the lever arm for internal stress. Ejecting a part before it has cooled enough also invites warp.
A checklist for the molding floor
Measure both mold halves. Use a surface pyrometer on the core and cavity in the area that warps. A large difference is the first thing to fix.
Check water. Confirm flow and temperature in every cooling circuit. A restricted line or a circuit that was never connected is a common surprise.
Look at the direction of warp. Parts bow toward the side that shrank more, which is usually the side that cooled more slowly.
Review the packing profile. Compare part dimensions near the gate and at the end of fill, and adjust packing pressure if they differ.
Extend cooling time before ejection and see whether the warp changes.3 If it does, the part was coming out too soon.
Change melt temperature last. Paulson Training recommends verifying melt temperature with a hand pyrometer and changing it last, because it affects every other variable.
Escalate to design and material if process changes do not hold: uniform walls, symmetrical geometry, appropriate rib thickness, or a lower-shrinkage grade.
Why process consistency matters
Warpage often shows up as variation: some shots are flat and some are not. That is a sign the process is sitting near the edge of its window. Consistent injection speed and pressure from shot to shot keep orientation and packing the same every cycle. LOG Injection Molding Machines’ S-9 Series provides real-time control over injection speed, pressure and screw position with closed-loop control, built for repeatability across a production run.
Machines mentioned in this article
Real-time control of injection speed, pressure and screw position with closed-loop control
View machine →
Replacement parts for LOG Injection Molding Machines, including heater bands and electrical components
View machine →
Chasing variation from shot to shot?
Talk to LOG Injection Molding Machines about the injection control and repeatability your parts need.
Frequently asked questions
What causes warpage in injection molding?
Warpage is caused by uneven shrinkage within the part. The main sources are uneven cooling, uneven packing from gate to end of fill, molecular or fiber orientation, material choice, part design and ejecting parts before they have cooled enough.
Which way will a part warp?
A part generally bows toward the side that shrank more, which is usually the side that cooled more slowly. Paulson Training’s rule is that the plastic that cools the slowest shrinks the most.
Does mold temperature affect warpage?
Yes. A large temperature difference between the core and cavity sides of the mold is a leading cause of warpage. Balanced mold temperatures are one of the first things to check.
Are some plastics more likely to warp?
Semi-crystalline materials with high, direction-dependent shrinkage, such as polypropylene and nylon, are more prone to warp. Fiber-reinforced grades generally shrink less but can warp directionally if fiber orientation is uneven.
How thick should ribs be to reduce warpage?
A PlasticsToday analysis suggests ribs of 30% to 50% of the wall thickness, noting that ribs thicker than 50% can act as heat sinks.

